WR-2001 Deep Hollowing System
This tool has been specifically
designed to provide a safe method for reaching into semi enclosed forms. The
7/8 OD shaft is filled with lead shot to dampen vibration and will accept any of our tools as well as other brands of hollowing
tools with a .500 diameter shank.
The WR-2001 Deep Hollowing
System comes complete and ready to use. You get the handle length of your choice, a Bent Shaft Boring Bar, Swivel Tip Holder
with a 3/16 cutting tool and a scraper blade.
The Adjustable Side Handle is designed to give turners additional
support and control of the main handle. Simply slide the handle onto the tool shank, adjust to the desired position and you're
ready to go.
Cutting Tools
Gouge
This gouge is used for general purpose turning including twig pots, bowls or boxes, detail work, pens and other simuilar
work.
Scraper
Scrapers are essential, particularly for interior clean-up work after the gouge work has been completed. Most bowls,
boxes, goblets and scoops benifit from light scraping cuts completing the final shaping and improving the surface.
Hooker Tool
This tool will allow you to easily reach under the lip of your work.
141 Hooker Tool - $28.00
Boring Bar
The Boring Bar accepts a 3/16 bit the same as the bent shaft boring bar. It is good for going straight down a vessel.
145 3/16 Boring Bar - $22.00
Adaptors
These adaptors allow you to use tools that have 5/8” shaft or 3/4" shaft.
The adaptor fits in your tool handle.
146.....5/8” Adaptor - $18.00
147.....3/4
Adaptor - $18.00
”Stingers” Round Point Cutter
Stingers use round cutting tools and are used for
roughing cuts. You can grind the bevel and use them like a gouge.
132 1/8 Tool with Holder - $18.00
133 3/16 Tool with Holder - $20.00
134 1/4 Tool with Holder - $22.00
Replacement Parts
Swivel Tip Holder with Cutter
This assembly mounts
on the Bent Shaft Boring Bar and is used for most of the hollow turning process and consists of a square tool bit cutter that
rests in a swivel holder allowing you to rotate and adjust the position of the cutter depending on your needs. You can pick
from 3 sizes 1/8”, 3/16” and 1/4". The further you get from the tool rest and the harder the wood, the smaller
tool you want to use.
125 1/8”
Swivel Tip Holder with Cutter - $10.00
126 3/16 Cutting Tip Holder with Cutter
127 1/4 Sivel Tip Holder with Cutter - $14.00
Square Cutter Tip Replacements
128 1/8 Cutting Tool - $4.00
129 3/16 Cutting Tool - $5.00
130 1/4 Cutting Tool - $6.00
Shear Scraper Blade
This mounts on the Bent Shaft Boring Bar and can be mounted with any of the
Swivel Tip Holders. This tool allows you to take fine, ribbon-like cuts when finishing the piece.
131 Scraper Blade - .$8.00
”Stingers” Round Point Cutter Replacement Tips
Stingers use round cutting tools and are used for roughing cuts. You can
grind the bevel and use them like a gouge.
135 1/8”
Tool Replacement - $4.00
136 3/16 Tool Replacement - $5.00
137 1/4 Tool Replacement - $6.00
Tool Handle
This tool has been specifically designed to provide a safe
method for reaching into semi enclosed forms. The 7/8 OD shaft is filled with
lead shot to dampen vibration and will accept any of our tools as well as other
brands of hollowing tools with a .500 diameter shank.
138
18” Handle - $34.99
139 24" handle - $39.99
140 36" Handle - $49.99
The Behemoth boring bar with
adjustable tip is used for hollowing out vessels. The adjustable end should be
offset and the cutting tip is adjusted to have the cutting edge on the center line of the tool. Set in this way, the inside walls of a vessel can be done easily with precise control.
122 Bent
Shaft - $24.99
123 Straight Shaft - $24.99
|
